OBDSTAR X300 DP PLUS Program 2020+ Honda Acura AKL

Here we'll demonstrate how to program 2020+ Honda Acura Civic all keys lost with OBDSTAR X300 DP PLUS by OBD. The operation procedure goes the same way with OBDSTAR X300 PRO4 as well.

Plug the connector into the OBD port.

CAR IMMO >> Asia >> HONDA ACURA >> Latest Version >> HONDA >> Manual select model >> ASIA >> CIVIC >> PROXIMITY >> BUTTON >> TYPE3(2019-)

Double-click the start button, ignition is still off, click "Esc".

If the ignition is on, please click "Enter".

Press and hold the start button until the ignition is on.

The ignition is turned on, please release the engine start/stop button.

Click "All smart keys lost".

Programming conditions:

1. No fault codes.

2. Make sure you have all proximity keys to be programmed.

Programming notes:

Make sure the following matters, in order to minimize the noise source when programming the proximity key.

Turn off the switch, such as a navigation system and audio.

Keep the proximity key and the diagnostic tool separated by approximately 1m(3 feet).

Close all windows, sunroofs, and doors.

Click "Enter".

This function will erase all keys, press ENTER to continue.

Turn off the ignition.

(Press the engine start/stop button. Be careful not to depress the brake.)

Please place an original proximity key in the vehicle.

Remove all the proximity keys in the vehicle.

Double-click the start button, ignition is still off, click "Esc".

If the ignition is on, please click "Enter".

Press and hold the start button until the ignition is on.

The ignition is turned on, please release the engine start/stop button.

Is it a new model(generally refers to models of 2020 and later)? Click "Enter".

This function is available by connecting the server, please ensure the Internet connection is normal.

Input the number of smart keys to be registered: 2

Take out all the registered proximity keys from the vehicle(make sure they are two meters away from the vehicle).

Only take one new smart key into the vehicle within 100s.

The smart key has properly been registered.

Remark: there can only be one key in the car, especially if all key lost, otherwise the key programming may fail.

Turn off the ignition.

(Press the engine start/stop button. Be careful not to depress the brake.)

Turn on the ignition.

(Press the engine start/stop button twice. Be careful not to depress the brake.)

IMMO indicator is off, press ENTER.

Turn off the ignition.

(Press the engine start/stop button. Be careful not to depress the brake.)

Turn on the ignition.

(Press the engine start/stop button twice. Be careful not to depress the brake.)

Registration has been completed.

Turn off the ignition.

(Press the engine start/stop button. Be careful not to depress the brake.)

Turn on the ignition.

(Press the engine start/stop button twice. Be careful not to depress the brake.)

Click "Key Quantity".

2 keys are registered in the ECM/PCM.

Test the new keys, all can work.

Done.

This is how to program 2020+ Honda Acura all keys lost with Key Master DP Plus.

www.obd2shop.co.uk

Toyota 89170-06790 Airbag Reset by bench with OBDSTAR P50

This post will guide you on how to use the OBDSTAR P50 Airbag Reset Tool to do a Toyota 89170-06790 airbag reset by bench.

Preparation:

P50

Main Cable

P004 Jumper + P004 Adapter

Toyota 89170-06790 Airbag ECU

Procedure:

Please keep P50 in charge and communication throughout the whole process.

Click "Airbag Reset" on the main interface, then select "Airbag Reset V30.48" >>"Brand" >> "Toyota".

Check the part number on the ECU label.

Input the part number of ECU (case insensitive, fuzzy search supported)

Remarks: Click operation instructions at the bottom left to check the best detection method.

Click" Pinout"

Connect the harness according to the wiring diagram, then click "Start" to continue.

Click "ECU information" to check if the airbag part number is correct.

Click "Read DTC", there is a crash fault code, then we click "Erase Crash" to perform the operation.

This function is available by connecting the server, please ensure the internet connection is normal.

Erase Crash success.

After the operation is done, read DTC again.

No crashfault code! The airbag reset is done!

Video Guides:

www.obd2shop.co.uk

OBDSTAR DC706 Read & Write Ford 6000CD Radio Code

This is a tutorial on how to read and write Ford 6000CD radio code with OBDSTAR DC706 by bench. It can also support to clone EEPROM. Read this article to learn step by step.

Accessories

DC706 ECU Tool

P004 ECU Clone Adapter + Jumper

Main cable

Ford 6000CD

Please keep DC706 charging and communicating during the whole process.

Operation

ECU Flasher >> BODY/ CHASSIS/ OTHER >> Latest version >> BRAND >> FORD >> FORD RADIO VISTEON 6000CD TMS470(OBD/BOOT)

Press "Guide/Pinout" to check the best detection method.

Connect the harness according to the wiring diagram.

After a successful connection, press

Start >> OBD >> OK

This function is available by connecting the server, please ensure the Internet connection is normal.

Switch on P004 ignition.

Press "Code Read".

Writing bootloader...

Pincode read successfully:1234

Reboot and enter the pincode on Ford 6000CD radio for verification.

Pincode verification is successful.

Press "Code Change" to change the pin code: 4321

Operation success.

Reboot and verify the changed pincode on the 6000CD radio.

Pincode changed successfully.

Press "Code off".

Security verification in progress...

Operation success.

Next, we can also read/write EEPROM (24C16) for radio ECU cloning.

Save EEPROM's success.

WriteEEPROM(24C16) >> Load external data

Writing EEPROM...

Writing success.

The read-and-write EEPROM operation is completed.

www.obd2shop.co.uk

Obdstar X300 DP Plus Adds 2023 Toyota Land Cruiser Key

Today I'm working on a 2023 Toyota Land Cruiser, and I am trying to make a new key for this vehicle with Obdstar X300 DP Plus. This is the original key and a new key. The procedure will need to send car number data to a third party for security code.

Connect Key Master DP Plus to OBD,

CAR IMMO >> TOYOTA LEXUS SCION >> Latest version >> Manual select system >> PROXIMITY >> TYPE 8(CAN) >> Number of keys

Current number of keys: 2

Press "Add keys".

This function is available by connecting the server, please ensure the Internet connection is normal.

This function is used to program the keys. Up to 6 keys can be programmed.

Note: Please complete all steps within the specified time.

Press "Enter" to continue.

Switch the ignition on.

X300 DP Plus shows the car number data.

Please send the above data to a third-party platform to get a 12-digit security code(please do not exit this interface during the query), please enter the 12-digit security code after obtaining it.

Use a programmed smart key to contact the start button.

Use a new smart key to contact the start button.

Program complete.

Test both keys, all can work.

This is using Obdstar X300 DP Plus to program the 2023 Toyota Land Cruiser by OBD successfully.

www.obd2shop.co.uk

OBDSTAR DC706 Clone BMW MSV90 ECM on Bench

This is a quick guide on how to use the OBDSTAR DC706 ECU Tool to clone BMW MSV90 ECM on bench. Besides, it also supports clone MEVD17.2.6 EXX, MEVD17.2.6 FXX, MSD80, MSD85, and MSD54 ECM. For details please refer to the below chart.

BMW ECM Support List:

Tools Required

OBDSTAR DC706

Main cable

P004 Adapter + P004 ECU Clone Jumper

BMW MSV90 ECM

Please keep DC706 charging & communicating throughout the whole process.

Operation Process

ECU Flasher >> ECM >> Latest version >> BMW >> BMW Continental MSV90 TC1796(BENCH) >> Start

This function is available by connecting the server, please ensure the Internet connection is normal.

Remarks: Click operation instructions at the bottom left to check the best detection method.

Connecting the harness according to the wiring diagram.

Follow the interface prompts:

Switch the ignition off.

Switch the ignition on.

Read INT eeprom, INT flash(TC1796), Maps, and ISN code.

Please check the log on the left side screen to see the saved path of reading data.

After successfully saving, write INT eeprom, INT flash(TC1796), and Maps.

The ECU clone operation is completed.

Remember to disconnect before exiting.

www.obd2shop.co.uk