OBDSTAR DC706 Volvo HCM R/W Data, Coding, Change Left Side

This article will demonstrate how to use OBDSTAR DC706 to read and write data, read coding, and modify left or right-side settings on the Volvo HCM module. It also supports OBDSTAR X300 Classic G3.

Required Tools:

DC706 ECU Tool

High-power DC regulated power supply

Main cable

ECU clone jumper

120Ω resistor

MP001 Programmer

Volvo HCM module

Procedure

Before proceeding, you need to upgrade the software to the latest version.

ECU Flasher >> BODY/CHASSIS/OTHER >> Latest version >> VOLVO HCM(OLD) CONTINENTAL RIGHT R7F7010244 >> Pinout >> BENCH, MP001, OK

Check if the module's appearance is consistent.

Click "Guide" and carefully read the warm reminder, function description, operation introduction, and connection method.

Connect the device according to the wiring diagram.

After connecting, click "Start".

BENCH >> MP001 >> OK

This function is available when connecting to the service. Please ensure the Internet connection is normal.

Click "Connect >> OK".

Here, we can read and write coding, read and write INT flash(R7F7010244), and change the left side.

www.obd2shop.co.uk

OBDSTAR MQB All Keys Lost RH850/V850 Adapter New Release!

Good news! OBDSTAR MQB ALL KEYS LOST RH850/V850 Adapter will arrive next month and is available for pre-order now. Used for airbag reset, immo data/pin code read(dashboard, BCM, ELV, etc.) 

Note:

1. Need to work with OBDSTAR X300 Classic G3 + MP001 Set.

2. All data read is unencrypted and can be used on third-party devices.

RH850/V850 Adapter Kit

Includes C4-06, W010, W010A, C4-06-C04, C4-06-C02, Dedicated decryption jumper(5 sets), MQB Collector, ECM-001, M002, TCM-MAIN, Converter V2, TCM-030, TCM-KIT 1 or TCM-001+TCM-002+TCM-005(can be purchased separately).

Supported Functions

 Volkswagen MQB48-5A key programming(components removing free) (MQB49-5C under development)

 Ford/Lincoln 2021- key programming (including all keys lost)

 Nissan/Renault key programming (including all keys lost)

 FCA key programming (upcoming upgrade)

 Airbag reset

www.obd2shop.co.uk

PIAGGIO PGQ 168 ECU IMMO Off by OBDSTAR X300 Classic G3

This post will guide you in using the OBDSTAR X300 Classic G3 Programming tool to disable the immobilizer on a Piaggio motorcycle.

Repair Background:

When encountering issues such as a damaged key chip, signal interference, or anti-theft module failure that prevent the vehicle from starting, you can disable the immobilizer function and use a temporary blade key to start the car.

You can also disable the immobilizer function during vehicle circuit repairs or ECU debugging to avoid interruptions caused by anti-theft lockouts.

The tools we need:

Key Master G3

High-power DC regulated power supply

Main cable

ECU Jumper

P004 adapter

PIAGGIO 168 ECU

Before proceeding, you need to upgrade the software to the latest version.

Select [IMMO] >> [ MOTO] >> [PIAGGIO] >> [PIAGGIO V40.31] >> [PIAGGIO]

Slect [Manual Select System] >> [PGQ16/PGV18]

Open the [Guide] section and carefully read the function instructions, menu description, operation instructions, and connection method.

Follow the wiring diagram for the connection.

After completing the connection, read the ECU information to verify its accuracy.

Proceed to read the MAP data and save it after reading.

Tap [IMMO-ON/IMMO-OFF] (Note: This function requires an internet connection to execute.)

Please back up MAPS before changing the IMMO status!

Current IMMO status: ON

CRC check result: success

Turn off the immobilizer?

Click "Yes" to continue.

Operation success.

Above is using OBDSTAR X300 Classic G3 to disable the immobilizer on a Piaggio motorcycle.

For more details, please refer to the video:

www.obd2shop.co.uk

Renault Delphi DCM3.4 ECU Mileage Calibration by OBDSTAR X300 Classic G3

This post will show you how to use OBDSTAR X300 Classic G3 to perform the mileage recalibration function on the Renault Delphi DCM3.4 engine ECU.

The tools we need:

X300 Classic G3

High-power DC regulated power supply

Main cable

ECU clone jumper

P004 adapter

Renault Delphi DCM3.4 engine ECU

Before proceeding, you need to upgrade the software to the latest version.

Open [ODO Meter], and in the top right corner, enter a keyword to select quickly.

Then we click [RENAULT/DACIA] >> [RENAULT/DACIA V41.16] >> [ECM] >> [RENAULT] >> [DELPHI] >> [DCM3.4]

Open the [Guide] section and carefully read the menu description and special note.

First, open the P004 adapter and check the [ECU Info.]

Check [Mlieage Read]

Tap [Mileage Calibration] and input the mileage as you need.

Mileage repair successful.

According to the prompt, we need to unplug one IG(ignition) wire and wait one minute before reconnecting it.

Video guides:

www.obd2shop.co.uk