Obdstar X300 DP Plus Adds 2019 Nissan Sylphy(B18) Key

Obdstar X300 DP Plus is able to program the 2019 Nissan Sylphy B18 proximity key with a free pin code by OBD. Need to work with NISSAN-40 BCM Cable for the process. Read this guide to learn how to do it.

Check the video to learn:

Preparation

Remove the trim panel under the dashboard and locate the BCM module.

Connect NISSAN-40 BCM Cable to BCM module.

Connect to Key Master DP Plus via the main cable.

Operation

CAR IMMO >> NISSAN INFINITI >> Latest Version >> Manual Select System >> 28 Digital Pincode >> SYLPHY(B18)/SENTRA >> PROXIMITY >> 2019- >> Add Keys(Free Pincode)

This function is available by connecting the server, please ensure the Internet connection is normal. Press "Enter".

This function continues to need to unplug the gateway interface, and then use the dedicated Nissan/Renault 16+32 interface to connect to the unplugged gateway interface.

Press "Enter" to continue.

Note:

1. Executing this function will clear all the keys of the vehicle. The deleted keys must be re-programmed before they can be used normally;

2. Only 2 new keys can be programmed each time. If you need to program more than 3 keys. Please divide them into 2 operations;

3. There must be at least 1 key that can start the vehicle normally;

4. After the 4-button smart key programming is completed, if the transponder and the smart are not normal, please try to Write HEM Confin.

Warning:

1. To ensure that the pincode is successfully read, please turn on the ignition switch;

2. The device must not be disconnected during the pin code reading process. Otherwise, the module will be damaged;

3. Please check the vehicle voltage, line connection, and other conditions to prevent the device from connecting abnormally in the middle.

Press "Enter".

Writing data, please wait for about 5 minutes...

The current 28-digit pincode has been read out.

This pin code can be used when all the keys of the current vehicle are lost to perform key programming operations.

Press "Enter".

Turn on the double flash, and turn off the ignition switch.

Switch the ignition on.

1. Long press the start button to turn off the ignition switch;

2. Turn on the hazard warning lights(double flashing lights);

3. The gear position is in P gear or neutral gear;

4. The steering column lock is in the unlocked state.

Start to read the key ID:

Place the 1st smart key to be programmed(with the mark upward) flat above the ignition switch, the key end with the mark is directly above the ignition switch, and other smart keys are far away from the ignition switch.

Special note:

1. Do not move the key on the ignition switch;

2. Do not press any button of the smart key;

3. Do not insert or remove the blade key in the smart key.

Press "Enter".

New key number: 0

Old key number: 1

Current total key number: 1

Note:

1. Here you need to read all key IDs to be programmed;

2. New keys can only be programmed at most 2 keys, the total number of keys is up to 4; Press "Enter" to read the next key, "Esc" to the next step.

Start programming the key:

Place the 1st smart key to be programmed(with the mark upward) flat above the ignition switch, the key end with the mark is directly above the ignition switch, and other smart keys are far away from the ignition switch.

Special note:

1. Do not move the key on the ignition switch;

2. Do not press any button of the smart key;

3. Do not insert or remove the blade key in the smart key.

Press "Enter".

The key is being programmed, please do not move the key...

Program success.

Number of keys successfully programmed: 1

Follow the following operations to complete the programming functions:

1. Turn off the hazard warning lights(double flashing lights);

2. Press the lock and unlock button of each smart key one by one to verify whether it is normal;

3. Check one by one whether each smart key can be put into the car to start the car;

4. After completing the above operation, press "Enter" to end the function.

After all keys have been verified, please do not exit this function, press "Enter" to continue after completing the operation according to the following prompts:

1. Remove the dedicated Nissan/Renault 16+35 connector and restore the gateway module;

2. Connect the device to the vehicle OBDII connector and turn on the ignition switch.

Program success.

www.obd2shop.co.uk

OBDSTAR D800 Marine Intelligent Diagnosis Recommendation

OBDSTAR D800 is a new generation diagnostic tool for marine, working for jet skis, outboard, inboard, and generators. Based on the Samsung Exynos processor and the new Android 5.1.1 system, D800 is fast and smooth to be a good helper for marine maintenance engineers.

Software

There are 2 software configurations for selection: D800A & D800B

Features

1. Provides complete diagnosis including checking ECU info, reading & clearing codes, data flow, freeze frames, actions test, setting, coding, etc.

2. Record and playback real-time flow, which allows users to accurately locate sensor and component faults.

3. Can work with OBDSTAR APP to get more functions than the D800 device itself. Such as diag socket location, flash code query, technical bulletin, service lamp reset, basic parameters, etc.

4. OBDSTAR technical staff one-click remote assistance.

5. One-click software upgrade via Wi-Fi.

6. Supports advanced functions such as Auto Scan, Active Trim Configuration, Active Trim GPS Configuration, Auxiliary Joystick Configuration, BCM Simulator, Compass Configuration, Device Initialization, Drive Alignment, Helm Setup, Instance Setting, Maintenance Setting, Merc TDS Reset, Remote Control Reset, Set Engine Location, Set Tach Link, Set Tilt Limit, SMUX Congfiguration, Steering Wheel Centering, System Calibration, Torque Adjustment, Trackpad Configuration, Vessel Personality, etc.

Supported Brands

EVINRUDE, HIDEA, HONDA, JOHNSON, KAWASAKI, MARINER, MERCURY/MERCURY RACING, PARSUN, SEA-DOO(BRP), SELVA MARINE, SEVEN MARINE, SUZUKI, TOHATSU, YAMAHA...

Optional Brands

CATERPILLAR, CFMOTO, CRUSADER ENGINES, CUMMINS MARINE, CUMMINS MERCRUISER DIESEL, DAEDONG, DAF MARINE, FNM MARINE, FORD MARINE, FPT (Fiat Powertrain Technologies), HYUNDAI SEASALL, ILMOR, INDMAR, JOHN DEERE MARINE, KODIAK MARINE, KOHLER POWER SYSTEMS, LOMBARDINI MARINE, MALIBU, MAN MARINE, MARINE POWER, MTU, PANTHER AIRBOATS, PCM Marine Engines, PERKINS, SCANIA MARINE, SISU, STEYR MOTORS, TOYOTA MARINE, VM MOTORI, VOLKSWAGEN MARINE, VOLVO PENTA, YANMAR...

OBDSTAR D800 Diagnose Honda Outboards

Connect D800 to Honda outboard via M001B cable & M015A Honda cable.

Marine Diag >> HONDA >> Latest version >> Diagnosis >> Serial A >> AquaTrax F-12(ARX1200N3) >> ENG >> Honda PGM-FI(2004-) For the US/CANADIAN >> DTC

Here we can read DTC, read the data stream, and do the active tests, and special functions.

Operation video:

OBDSTAR D800 Diagnose YAMAHA Outboards

Connect D800 to YAMAHA outboard via M001B cable & M061 YAMAHA cable.

Marine Diag >> YAMAHA >> Latest version >> Diagnosis >> ENG >> OK

Here we can check ECU info, read DTC, read data stream, and do active tests.

Operation video:

OBDSTAR D800 Diagnose Suzuki Outboards

Connect D800 to Suzuki outboard via M001B cable & M062 Suzuki cable.

Marine Diag >> SUZUKI >> Latest version >> Diagnosis >> Auto identify(CODE)

Here we can check ECU info, read DTC, read data stream, do active tests, and special functions.

Operation video:

www.obd2shop.co.uk

How to Download & Bind OBDSTAR App?

OBDSTAR APP has been blockbuster launched on the Android platform, go download and get started - maintain technicians' portable database. Working for most OBDSTAR diagnostic tools such as X300 DP PLUS, ODO Master, etc.

Where to download OBDSTAR App?

1. Scan the QR code to download.

2. Visit www.obdstar.com to download.

3. Download in Android software store, like OPPO, VIVO, Huawei, Xiaomi, etc.

ISO version will be launched at the end of June, please stay tuned.

Why use OBDSTAR App?

1. Supports locksmith IMMO & maintenance.

2. Supports car electronics maintenance and repair.

3. Supports motorcycle maintenance and repair.

4. Supports marine maintenance and repair.

5. Provides customer service.

How to bind OBDSTAR App with your device?

1. Make sure your OBDSTAR device is connected to the Internet;

2. Open device QR code:  Settings >> VCI Info >> Device QR code(network required)

3. Scan to bind on App: Me >> My device >> Device binding >> To bind

When successfully binding, the device details will be shown on the app.

Operation video:

Download OBDSTAR App now to play with massive maintenance solutions.

www.obd2shop.co.uk